塑料件卡扣等設計標準模塊自創推薦新人學習

塑料件卡扣等設計標準模塊自創推薦新人學習當前1頁，總共33頁。2目錄1.柱位結構······································································3

優缺點及使用范圍······················································42.螺釘沉孔·······································································5

優缺點及使用范圍·······················································63.

帶罩蓋的螺釘沉孔····························································7

罩蓋········································································8優缺點及使用范圍·······················································94.金屬卡口支撐臺（單邊卡位）··············································10雙邊卡位··································································11金屬卡口··································································12

優缺點及使用范圍·······················································135.椅背板鋼絲卡·································································14優缺點及使用范圍·······················································156.鋼絲卡··········································································16

優缺點及使用范圍·······················································177.平板卡口連接··································································18

結構分析··································································19

優缺點及使用范圍·······················································208.卡口連接與翻邊·······························································21

結構分析··································································22

優缺點及使用范圍·······················································239.插片式卡口連接·······························································24結構分析·································································25優缺點及使用范圍······················································2610.圣誕樹支撐···································································27

優缺點及使用范圍·····················································28

圣誕樹例樣······························································2911.塑料支腳·····································································33

優缺點及使用范圍······················································34

當前2頁，總共33頁。3柱位的設計方式-自攻螺釘自攻螺釘規格（國標）螺釘柱內徑?（mm）nd螺釘柱外徑（mm）wdST2.21.75ST2.92.36ST3.52.87ST4.23.47.5ST4.83.88ST5.54.49自攻螺釘?shù)臉藴食叽绫韮?nèi)值為參考值，一般柱位內徑較nd大0.3~0.4mm，柱位壁厚在1.25mm左右，以防止產品表面縮凹。柱位高一般在5～10mm。當前3頁，總共33頁。4柱位結構的優缺點及適用范圍用途：將零部件（開關盒，鉸鏈等）固定到塑料件上。優點：結構簡單，固定牢固。缺點：產品表面容易縮凹，裝配工序較煩。適用產品：旁側板等需要固定零部件的塑料件。當前4頁，總共33頁。5DB_PART_NOOS_PART_NAMEstdKdkI

1ST2.22.21.646.52ST2.92.92.45.69.53ST3.53.52.679.54ST4.24.23.189.55ST4.84.83.79.5136ST5.55.541113螺釘沉孔自攻螺釘?shù)臉藴食叽鐂td為螺釘螺紋處直徑；K為螺釘頭部厚度；dk為螺釘頭部直徑；l為螺釘螺紋處長度；t為產品壁厚；Δ根據公差要求進行設定。當前5頁，總共33頁。6螺釘沉孔的優缺點及適用范圍用途：用螺絲固定塑料件。優點：裝配簡單,可拆卸,定位性好。缺點：裝配位可見，容易粘定模導致產品拉壞。適用產品：適用于大部分塑料件的非可見區，如設在可見區，必須得到客戶同意。粘定模對策當前6頁，總共33頁。7帶罩蓋的螺釘沉孔H<1.5D,定模側壁脫模斜度大于5度。此標準件為裝配件，裝配后蓋子與本體要求無間隙、晃動、斷差，且紋理一致。當前7頁，總共33頁。8罩蓋當前8頁，總共33頁。9帶罩蓋的螺釘沉孔的優缺點及適用范圍用途：用螺絲固定塑料件,并遮蓋孔位。優點：裝配簡單,可拆卸,定位性好，看不到螺釘。缺點：容易粘定模導致產品拉壞，多一道裝配工序，表面有縫隙。適用產品：適用于大部分塑料件一般要求外觀面，使用時必須得到客戶同意。當前9頁，總共33頁。10金屬卡扣支撐臺（單邊卡位）h=H-6.5(當H<=20時)；

h=0(當20<H<=30時);h=13.8(當30<H時)。當前10頁，總共33頁。11金屬卡扣支撐臺（雙邊卡位）單邊卡位受法向力時金屬卡扣可能歪斜。雙邊卡位受法向力時金屬卡扣可能會拉斷塑料件。當前11頁，總共33頁。12金屬卡扣可拆卸式卡扣不可拆卸式卡扣當前12頁，總共33頁。13金屬卡扣支撐臺的優缺點及使用范圍用途：裝配CLIP后使塑料件固定在金屬板上。優點：裝配簡單，可承受法向拉力及壓力，高度調節范圍大。缺點：裝配后有一定晃動量，對切向受力抵抗弱。適用產品：旁側板、前擋板等塑料件，位置較自由。當前13頁，總共33頁。14椅背板鋼絲卡扣詳細請參照圖紙其他規格鋼絲可參照此形狀適當更改。H值一般在20mm左右。當前14頁，總共33頁。15椅背板鋼絲卡扣的優缺點及適用范圍用途：用鋼絲固定塑料件。優點：裝配簡單,可拆卸,位置可適當調節。缺點：定位差，需靠其他定位機構輔助。適用產品：椅背板上端，一般于左右上角設2處。當前15頁，總共33頁。16鋼絲卡扣其他規格鋼絲可參照此形狀適當更改，開口尺寸在鋼絲直徑的60％左右。當前16頁，總共33頁。17鋼絲卡扣的優缺點及適用范圍用途：用鋼絲固定塑料件。優點：裝配簡單,可拆卸,模具上易實現。缺點：高度有限制,受力有脫落可能。適用產品：旁側板、前擋板等塑料件，卡扣周圍50mm左右范圍內無發泡或面套擠壓。當前17頁，總共33頁。18平板卡扣連接當前18頁，總共33頁。19平板卡扣連接－－結構分析當前19頁，總共33頁。20平板卡扣連接的優缺點及適用范圍用途：平板件與其他塑料件利用卡扣連接。優點：裝配簡單且牢固，適用性強。缺點：需要其他結構支撐板件。適用產品：適用于板件與一般塑料件的連接等，板件一般不屬于重要外觀件。當前20頁，總共33頁。21卡扣連接與翻邊當前21頁，總共33頁。22卡扣連接與翻邊－－結構分析當前22頁，總共33頁。23卡扣連接與翻邊的優缺點及適用范圍用途：塑料件之間的相互固定。優點：裝配簡單且牢固，適用性強，對內部結構起到遮蔽作用。缺點：受法向拉力有限，翻邊易損。適用產品：適用于各種塑料件的相互固定，例如外側飾板與內側飾板的連接、扶手盒的結合等。當前23頁，總共33頁。24插片式卡扣連接當前24頁，總共33頁。25插片式卡扣連接－－結構分析當前25頁，總共33頁。26卡扣連接與翻邊的優缺點及適用范圍用途：塑料件之間的相互固定。優點：結構簡單,裝配容易，空間占用小。缺點：受力易脫落，需和其他卡扣配合使用。適用產品：例如外側飾板與內側飾板的連接等。當前26頁，總共33頁。27圣誕樹支撐臺圣誕樹當前27頁，總共33頁。28圣誕樹支撐臺的優缺點及適用范圍用途：利用圣誕樹來防止外表面浮起(提供法向拉力)。優點：裝配簡單,可拆卸,模具上易實現。缺點：安裝后高度不穩定,對切向受力抵抗弱。適用產品：旁側板、椅背板等塑料件。當前28頁，總共33頁。29零件號零件名稱D1D2L1L2ApplicationForcerequirement1442633W-CLIP-PLASTICW型塑料卡子

51814.32Hole:Φ9.0±0.12

Thickness:2.75mmInsert≤80N

Extraction≥334N圣誕樹例樣當前29頁，總共33頁。30零件號零件名稱D1D2D3L1L2L3L4L5ApplicationForcerequirement1325904CB－07000－00CLIP塑料夾子

154.66.819.31.310.816.6Hole:Φ7.0+0.1

Thickness:1.5-3mmInsert≤150N

Extraction≥200N當前30頁，總共33頁。31零件號零件名稱D1D2D3d1d2d3L1L2L3ApplicationForcerequirement1116415A-StyleXmasTreeClipA型塑料釘

3229.24863.12.81.72.75Hole:Φ7.0-7.25

Thickness:2.75±0.15mmInsert≤8LBF

60LBF≥Extraction≥40LBF1130072B-StyleXmasTreeClip