模具驗收檢查表(出口模具)

1、星諾奇科技 Sinnotech TechnologyQP-MD-01-27A 模模具具驗驗收收檢檢查查表表 Tool Check and Acceptance Checklist產產品品名名稱稱 PartName:PartName:模模具具編編號號Mold No: 產產品品圖圖號號 DrawingDrawing No:No: 版版本本號號 Version:Mould supplier has to certificate the following items:Yes NoAction01Is the mould number on the mould?模具上刻有與客戶公司內部標識一致的模具編

2、號 02Mould fit on the injection machine and dimension on for the mounting wholes is ok? 模具外型尺寸及各安裝孔位、尺寸與相應的注塑機臺匹配03Are the opening strokes concerning the assembly drawing? 模具打開的行程及推板頂出行程和水口板開模距離(僅適用于三板結構)與模具裝配圖紙上是否一致04Is a lifting block on the mould? 模具帶有與模具外形尺寸匹配的鎖模扁擔05Is draw bars balance good?模具有鎖

3、模扁擔和起吊孔并能夠保證模具平穩起吊 06Can tool open and close smoolthly?模具打開和閉合過程輕松、安全、平穩 07Is the diameter of the locating rings ok?定位圈的直徑尺寸正確并與相應的注塑機臺匹配 08Is there insulating plate ?有隔熱板 09Is the right radius on the sprue bushing/nozzle?澆口套進料處的球面直徑與相應的注塑機臺匹配 10Is there counter?有無計數器 11Are all big movable parts hav

4、ing lubricated groove?所有大的移動部件都有油槽 12Is the ejector unit moving easily?頂出系統運動足夠的輕松 13Correct screw thread on the ejector rod?頂出桿上的螺紋尺寸正確 14Is ejector pins fixed if it is not allowed to be rotated?所有頭部為非平面的頂針都有采取防轉措施 15Are all slides secured?所有滑塊的運動安全可靠（有限位裝置及防止脫出裝置） 16Can slider be moved by hand smo

5、othly and stably? 滑塊部件可以在用人手操作的情況下運動自如平穩17Connection for water/oil/hydraulic and air are labeled? 18各個種類的所有接口（包括水路、油路、液壓缸、氣壓）都有標示 19Cooling connector meet Customers requirement.水管連接頭符合客戶標準 20Is cooling plug pipe according to Customers spec?冷卻系統的水路堵絲符合客戶要求 21Did you test the cooling system for any le

6、aks (15 bar)?已經測試過冷卻系統的滲漏情況（15bar壓力下） 22Whether use Viton O-Ring which can be used on hign mold temperature ? 使用耐高溫的Viton材質的O形環 23All transition in the runner system must be round流道系統中所有過渡點(轉彎、交叉)都必須倒圓角 24Is the runner system vented?流道系統是否有排氣 25Is partline venting system good模具分型面的排氣是否良好 26Are the c

7、avities numbered (not on ejectors)? 所有模具型芯上都刻有相應的模穴號，此號碼應與模穴產品號相一致27Whether family mold have mold part list?Whether engrave marks on mold part? 共模的模仁有無部件清單？是否在模仁上刻上標識以區分？ 28Are the hydraulic connectors at the cylinders ok?液壓缸頭部與模具部件連接處完好，尺寸正確 29Is the function of any end switches tested? 模具上所有的非機械式開

8、關（電氣、磁性限位）及傳感器都經過功能測試并確保能夠正常使用30Is the function and the end switch for the unscrewing system tested? 31脫螺紋系統的功能及距離都經過測試并確保能夠正常使用 32Hot runner system: connecting line should be coved for preventing damage. 熱流道系統的電線應被覆蓋在模具內部以確保生產情況下不會被損害33If have hot runner,please fill value on below list 如有熱流道的模具請把加熱及感溫阻值填寫在下表中.序 號1 - 23 - 45 - 67 - 8加熱阻值感溫阻值34Whether Customers got latest mold drawing? 客戶是否收到最終的硬拷貝及電子檔模具圖 35Whether have spare part list?是否有備件清單 備注 Remarks:鉗鉗工工 Tool Maker生生產產部部 Workshop 項項目目 Project確確認認是是否否可可以以走