風扇安規中英文版-UL507 and CSA C22.2 No. 113 for Client-histo

1、1Electric FansUL 507/C22.2 No.113 產品結構及測試要求（For Electrical Fan）Prepared By: Histo LingIntertek GuangzhouAug 16, 2目錄Content of UL 507Part 1 General Requirements， for all product 通用部分；通用部分；Part 2 For specific product types 特殊類型產品特殊類型產品.Consist of:-Section 1 Mechanical Construction， 機械結構；-Section 2 Ele

2、ctrical Construction， 電氣結構；-Section 3 Components， 零部件；-Section 4 Safety Test， 測試；-Section 5 Marking and Instructions，銘牌、說明書。3Section 1 Mechanical Construction金屬外殼：金屬外殼：用于外殼的金屬材料厚度應滿足表6.1的要求（Exception: pass the impact test）：4非金屬外殼材料（熱塑、熱固）：非金屬外殼材料（熱塑、熱固）：一般指塑膠材料，根據標準要求需要進行鋼球沖擊測試（6.8J或1.02J）來評估材料的抗沖擊性

3、能。材料防火等級要求：材料防火等級要求：UL507要求HB以上，CSA C22.2 No.113要求5VA（Exception:如果處于高壓電路的帶電部件用5VA的材料包裹起來后，其周圍或外殼材料可用HB等級）。非金屬風輪（葉）材料：非金屬風輪（葉）材料：HB等級的塑料風輪與風輪電機外殼上開孔的距離不應小于25.4mm，如小于這一距離，需滿足以下要求：電機外殼開孔數量小于6，且開孔直徑不大于6.75mm或開孔面積不大于35.48 mm ；orHWI=12A）的1.25倍；Section 2 Electrical C11Internal Wiring1、需適當保護，通過外殼開孔，允許被測試手指觸

4、及，但不允許被鉤拉；2、內部導線的布線應遠離運動部件及帶銳利邊緣的部件，以防絕緣損傷。若穿過壁厚小于1.07mm的金屬開孔時，該金屬開孔需作折邊處理或在開孔處增加壁厚為1.2mm的套管，如下圖：3、線號：UL507沒有對線號作具體要求，滿足過流即可。CSA C22.2 No.113要求內部線線號最小為18AWG，電機引線在滿足如下情況下可放寬到24號線： 工廠裝配； 長度小于150mm； 被外殼包裹。4、絕緣厚度：CSA C22.2 No.113要求內部線絕緣厚度不小于0.4mm（1/32 in)（1007可滿足）。5、相關屬性需符合特定的使用環境要求，如電壓、溫度等。Section 2 El

5、ectrical C12Spacing2. Table 24.3 Min required spacings on printed-wiring board assemblies under the condition the PCB with coating.Section 2 Electrical C13Section 2 Electrical ConstructionSpacing3. CSA C22.2 No.113 - Table 5 for Min required spacings at bare live 14Grounding and Bonding(UL507) (UL50

6、7) 以下情況需提供接地：以下情況需提供接地：1、電壓大于150V；2、產品是Evaporate Cooler ;3、戶外用產品。Exception:1、外殼或相關可觸及的金屬部件不具備電氣連續性，如塑料外殼。2、產品結構滿足UL1097雙重絕緣的要求。接地的相關要求：接地的相關要求：1、防腐材質接地螺絲，size：No.10（4.8mm）以上；2、接地處需提供接地標志；3、綠色或黃綠色地線；4、滿足接地連續性測試。Section 2 Electrical Construction(CSA 113) (CSA 113) 以下情況需提供接地：以下情況需提供接地：1.商用或者工業用；（家用風扇不強

7、制要求接地）15Switches or other control devices1、開關的額定值不能小于其所控制的負載的額定值；2、主控開關應和火線連接；3、控制非電機感性負載（如變壓器、鎮流器）的開關，其額定電流應為所控制負載的額定電流的兩倍以上；4、如產品有白熾燈，控制該燈的開關需滿足下述要求： 需能控制“T”或“L”負載； 如是交流電，開關額定電流需為所控負載的6倍。如是直流電，開關額定電流需為所 控負載的10倍。5、如產品中有熒光燈，其控制開關的額定電流至少為所控鎮流器額定電流的2倍。Capacitor1、電機啟動電容，需經UL 810認證；2、X和Y電容需經UL1414認證或通過U

8、L1283耐壓、絕緣電阻及耐久測試。Section 3 C16Motor1、馬達應該具有UL或ETL認證，并符合UL 1004-1/2/3/4, CSA C22.2 No. 100和CSA C22.2 No.77的要求；2、A級絕緣系統馬達內的電氣部件、塑料部件以及絕緣材料須有相應的UL認證；3、B級以上絕緣系統馬達，除電氣部件、塑料部件要有認證外，還需提供相關的絕緣系統認 證。以下部件須經認證：以下部件須經認證： 塑膠、內部線、開關、奶嘴、熱縮套管、玻纖套管、PCB、變壓器、溫控器、保險絲、繼電器、壓敏電阻等。特別是馬達部品：漆包線，絕緣材料（絕緣紙，絕緣槽等）Section 3 C17UL

9、 507 & CSA C22.2 No. 113:-Leakage-Current Test -Starting Current Test -Input Test/ Rating-Temperature Test-Dielectric Voltage Withstand Test/ Dielectric Strength-Humidity Conditioning Test-Strain Relief Test #-Push Back Relief Test-Tests of Switches and Controls/ Overload-Impact Test on Guards #

10、-Static Force Test on Guards-Impeller Test for Portable Fans/ Impeller Test for Freestanding Fans and Window Fans #Section 4 Safety TestUL 507 & CSA C22.2 No. 113:-Drop Test #-Security of Handle Test-Stability Test #-Abnormal Temperature-Probe Test #-Resistance to Impact TestUL746C:-Resistance t

11、o Impact Test-Abnormal Operation Test-Severe Conditions Test-Mold Stress-Relief Distortion Test-Input to Motors T18Section 5 Marking and InstructionsMarkings Rating Plate: ETL Logo要求要求：銘牌應包括以下內容： -申請人或工廠名、商標；-型號名；-生產日期；-電氣參數；-Thermal Protected。 CONFORMS TO UL STD.507CERTIFIED TO CSA STD. C22.2 NO.11

12、3 19Markings銘銘牌牌CSA C22.2 No.113-2010要求有馬達保險類型的法文內容： “thermally protected” or “impedance-protected”And protection thermique or protection par impedance。Cautionary Marking1、所有警語須英、法雙語；2、根據不同的產品，可能會用到以下警語：Use only 125-Volt Fuse, 2.5 Amp Max；Cord Tag Marking： ：產品使用SPT-2-R電源線時須提供以下內容線標：a.Always Unplug T

13、his Product Before Installing or Replacing Fuses.b.Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.c.Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not rou

14、te cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.該線標須以英、法雙語提供，離插面不超過6英寸。Section 5 Marking and I20Instructions說明書須包含以下內容：READ AND SAVE THESE INSTRUCTIONSWARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any

15、Solid-State Speed Control Device.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.If it still does not fit, co

16、ntact a qualified electrician. Do not attempt to defeat this safety feature.refer to illustraton.產品使用SPT-2-R電源線時，說明書中還須提供以下內容：This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace

17、 the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.Do not

18、 operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.User Servicing Instructions - shall include specific instructions concerning how to physicall